Thursday 12 January 2023

Solved: Super MB Pro M6 + SSD (749/701) Network Problem

Problem: Super MB Pro M6 + V2022.12 WIN10 SSD has met network problem, it gave the error as below:

"Initialisierung des Diagnose-Multiplexers ist fehlgeschlagen.

Mogliche Ursachen:

Die Verbindung zwischen dem Diagnose-Multiplexer und der Diagnosedose ist unterbrochen.

Die Verbindung zwischen dem Diagnose-Multiplexer und dem Diagnosegerat ist unterbrochen.

Die Spannungsversorgung an der Diagnosedose (Klemme 30 und (oder)Klemme 31) ist fehlerhaft.

Hinweis:

Bei Verwendung des SDconnect den Verbindungsstatus uber das Toolkit prufen".


(Initialization of the diagnostic multiplexer is failed.

Possible causes:

The connection between the diagnostic multiplexer and the diagnostic socket is interrupted.

The connection between the diagnostic multiplexer and the diagnostic device is interrupted.

The power supply at the diagnostic socket(terminal 30 and (or) terminal 31) is faulty.

Notice:

The connection status when using the SDconnect check via the toolkit.)

solved-super-mb-pro-m6-ssd-749-701-network-problem-(1)

"Due to network problems, no connection to the SDconnect can be established(749)".

"No VCI found. (701)

No SDconnect is selected or the desired SDconnect cannot be selected".

solved-super-mb-pro-m6-ssd-749-701-network-problem-2

solved-super-mb-pro-m6-ssd-749-701-network-problem-3

Solution

MB Star Diagnostic Tool needs to revise IP when connecting via the network. Please follow the steps below to fix the problem.


Selected "Use the following IP address(S)"

IP Address(I): 172.29.127.113

Subnet mask(U): 255.255.255.0

solved-super-mb-pro-m6-ssd-749-701-network-problem-4

Technical Support

www.obd2shop.co.uk

Thursday 11 March 2021

Fixed! MB SD Connect C4 Software Unable to Start on Win10

Problem

MB SD Connect C4 software unable to start or automatically repair on Win10.

Solution

Step1. Go to advanced options;

fixed-mb-sd-c4-unable-to-start-on-win10-1

Step2. Go to troubleshooting;

fixed-mb-sd-c4-unable-to-start-on-win10-2

Step3. Go to start up settings;

fixed-mb-sd-c4-unable-to-start-on-win10-3

Step4. Start PC;

fixed-mb-sd-c4-unable-to-start-on-win10-4

Step5. Computer press F4 to enter state mode;

fixed-mb-sd-c4-unable-to-start-on-win10-5

Step6. Press the “Win+R” shortcut key to open the “Run” window, enter “MSConfig”, click OK;

fixed-mb-sd-c4-unable-to-start-on-win10-6

Step7. Select diagnostic start up, click OK.

fixed-mb-sd-c4-unable-to-start-on-win10-7

Thanks to Obd2shop engineer, MB Star SD C4 software problem was solved!

Any questions please contact us.

https://www.obd2shop.co.uk/


Friday 18 September 2020

How to solve mb sdc4 "configAssist" cannot open?

One user of mb sdc4 tried to activate Xentry and need to open "configAssist", got problem with it " unable to access service..." So he was unable to go through as the PDF guide on desk, to activate. 

mb-sdc4-configassist-unable-to-access-service-01

obd2shop.co.uk chief engineer solution: 

Enter into "Device Manager" to find "Service" then "configAssist ", then click on "Start" and "Ok". The problem will be solved.

mb-sdc4-configassist-unable-to-access-service-02

mb-sdc4-configassist-unable-to-access-service-03

Good luck!

mb sdc4 tech support: www.obd2shop.co.uk

Thursday 27 August 2020

Free download XENTRY Diagnostics OpenShell 09 / 2020 XDOS_20.9.4

 XENTRY Diagnostics OpenShell - PassThru (OpenShell 09/2020 Final - XDOS 20.9.4 ) - MEGA - Torrent.


XENTRY Diagnostics OpenShell 09/2020 (20.9.4) - final version - 

XENTRY Diagnostics PassThru 09/2020 (20.9.3) - final version -

XDOS_2020.06_(20.6.4)_direct_link

XDOS 2020.09 (20.9.4) direct_link - Final Version

XDOS OpenShell 2020-09  ( 20.9.4 )

https://mega.nz/file/hmoHXKoS#HYXsIOV4alSoZ7onsasz1GYWH-TMfgpeonyNwgVn1TE

XDOS 2020-09 Win7 Fixed Solution

https://mega.nz/file/tmYhEKhL#ZuvICMC0sW50KHcjdQYw7vAGr0dfitdpgf9e0KoEJyU

Background_XDPad_2020-09.rar

XDOS_09.2020_Missing_Pics_Fixed_x64.rar

Xentry Passthru 06.2020 [20.9.3] - Torrent.rar





Good to know: 

OpenShell 09 / 2020 XDOS_20.9.4 source is from forum (credits to @ Smallville).

The author didn't test it yet, but only the Xentry 06/2020 below:

https://www.obd2shop.co.uk/wholesale/latest-mb-sd-connect-c4-ssd-256gb-software.html (ssd version)

https://www.obd2shop.co.uk/wholesale/latest-mb-star-diagnosis-hdd.html (HDD version)

Enjoy!


Thursday 13 August 2020

 Using sdconnect c4 plus clone to access to Mercedes car model SL300-24 Dec 1990. 

Trying to interrogate MB WDB1290612Fxxxxxx

Every time I try to get diagnostics this happens "Switch ignition on" 

sdconnect-c4-clone-switch-ignition-on-problem-solution-01


No 1 black masses should earth?  no 8 yellow LS Can_H no 16 12V B+

Is this correct should there be any other cables connected instead of these?

sdconnect-c4-clone-switch-ignition-on-problem-solution-02


It only has 16 individual pins see photo above. There isn't one too old.


obd2shop.co.uk engineer replied:

Please change a new MB 38pin cable to connect the DLC on the car. 

sdconnect-c4-clone-switch-ignition-on-problem-solution-03

Another case:

I have a Chinese clone SD connect c4 from YANHUA factory, self test without any errors, all the firmware updates can be applied without any troubles at all, batteries fully charged, tried several OBD cables BUT i still get the "turn ignition on" and furthermore it cannot recognize the VIN of the connected car.

sdconnect-c4-clone-switch-ignition-on-problem-solution-04


Solution by @JarsaR:

It is easy to test cable with other one.

i just had Yanhua mux which has been in use for years, selftest was ok, Software was ok. But did not connect to car. Mux has the round connector pcb, which pins are soldered to pcb pads, they were loosen in heavy use. Some of cheaper clones has pins go thru the other pcb also, and soldered to pcb, i think Yanhua is more sensitive with her pads. I resoldered all pads and Mux is now perfect.


Confirmed: this solution is working perfect. Change obd socket, my sd connect worked %100..


Enjoy!

http://blog.obd2shop.co.uk/fixed-sdconnect-c4-clone-switch-ignition-on-problem/


Monday 10 August 2020

Vxdiag C6 is a good device for Xentry (reviews)

This article will answer the following two questions:

I'm thinking about purchasing a Vxdiag C6 device since its capacity to be activated for lots of brands. whether its a good or a bad idea? Vxdiag C6 is capable of anything C4 can? is Xentry or Passthru needed for Vxdiag?


VXDIAG C6 review:

I have been using a VXDIAG C6 (the new one with the LAN port and mini-USB jack) for sometime (I have the Xentry and ODIS licence).


From my experience, I can tell you it's a good device for Xentry.


I have been using it with Xentry 12.2019 and have tested it on a variety of cars (even on older DAS cars like W211). Every function I have tried on Xentry / DAS has worked so far.


- ignition status is detected automatically (like C4) and it reads the voltage no problem


It is advertised to work with DoIP modules, but I haven't tested this myself (there are videos on YouTube where they demonstrate this)


It does work wirelessly as advertised through Wi-Fi. 


It tried it on normal Xentry (not passthru). It should also work on Passthru as it has a passthru licence and can work was a passthru device


The way it works is - Allscanner develops a driver for Xentry which allows their device to work with Xentry (xentry sees the mux as a Xentry Diagnosis VCI)


A potential problem is that Allscanner has to develop a new driver for each new version of Xentry - so you may not be able to use the latest version of Xentry when it comes out - you'll have to wait till they release the driver for that specific version of Xentry (as of writing this, Xentry 03.2020 is the latest driver available)


When you install their software on a Xentry system, it will auto detect the Xentry version installed and will load the correct driver for you (convenient) 


It gets occasional firmware updates (through the allscanner software) - you dont have to connect to car to power it on, just plug it into USB it will power on and you can do the FW updates at your home.


I have not tried it with online SCN coding, so can't comment if that works.


Overall, I like it a lot and have not used my old C4 since I received this. (keeping the C4 in case older cars come by which require HHTwin etc)


ODIS has been a hit and miss - it does not work wireless (ODIS quits out) - wired connection works.


I got it at obd2shop.co.uk (Basic hardware + Benz license + HDD) - for this price I have no complaints with it. It's a bang for the buck tool.


Other option you have (if you don't want to go for clones), is to go for reputed passthru device like Scanmatik 2 PRO and use it with Xentry Passthru.


Hope this helps you.

http://blog.obd2shop.co.uk/vxdiag-c6-is-a-good-device-for-xentry-reviews/


Tuesday 30 June 2020

How to use Star DAS to update Mercedes W221 Module Software?

Here a usual case today where I updated 5-6 modules OFFLINE, engine, cluster, some Sam's and more with my MB STAR DAS system and a custom database on a W221, R230, W220 and W215 often have very important updates for engine and transmission also.

Automobiles have always been comprised of a complex system of parts that work together to allow it to function appropriately; this is especially true of vehicles today. Over time, the evolution of cars has progressed into the age of technology. The most advanced vehicle technology, as seen in high-end luxury automobiles and performance autos alike, allows drivers to experience technology in their everyday commutes. Mercedes-Benz is one of the top vehicle manufacturers in the country that employs the most recent technological advances in automotive engineering and design. Although computers have existed in Mercedes automotive engineering for decades, vehicle functioning and performance is now reliant upon computers and technology more so than ever before. Therefore, just as it is necessary to update your computer at home in order for it to function at its best, Mercedes owners must also commit to updating their vehicle computer software too. It helps to understand why updating your Mercedes software is important, so here's a little more information on how technology contributes to your vehicle's functioning:

Systems that Software Potentially Affects
Most of us don't realize how many of the systems in our vehicle are monitored or controlled with technology; just know that there are more than we can name! Of course the obvious software-controlled systems like radio controls, navigation, and temperature control have made their way into the digital age and need updates from time-to-time in order to function at their best. Beyond these obvious systems, you might be surprised to hear that your Mercedes relies on software to effectively manage emission controls, power train functions, Engine Management, Transmission and even safety systems like anti-lock brakes and airbags. Furthermore, vehicle manufacturers, including Mercedes-Benz have encountered problems that have lead to other recall issues related to the vehicle's computer and software. It is critical to stay abreast of any recalls related to your particular Mercedes, and you can do this by directly contacting your vehicle manufacturer.

update-mercedes-w221-module-software-01

update-mercedes-w221-module-software-02

update-mercedes-w221-module-software-03

update-mercedes-w221-module-software-04

update-mercedes-w221-module-software-05

update-mercedes-w221-module-software-06


Here the same car SCN online coding with Star DAS:


mercedes-w221-scn-coding-07

mercedes-w221-scn-coding-08

mercedes-w221-scn-coding-09

mercedes-w221-scn-coding-10

 Enjoy!

http://blog.obd2shop.co.uk/how-to-use-star-das-to-update-mercedes-w221-module-software/